---
title: "Open-source resin slicers compared, November 2026"
description: "Encrust, DragonFruit, mslicer and UVtools side by side: licence, language, platforms, formats, status and each project's own speed figure."
url: "https://encrust.app/blog/open-source-resin-slicers-compared/"
lang: "en"
updated: "2026-11-17"
---

[ Resin printing, file formats and how a slicer works](https://encrust.app/blog/)

Resin printing

# Open-source resin slicers, side by side

[By Vladimir Varvorkin](https://encrust.app/about/) Updated November 17, 2026 4 min read

Three open-source resin slicers written in Rust are out today: Encrust, DragonFruit and mslicer. UVtools works on files that are already sliced. Encrust checks every layer of the file it writes and is the one of these with a browser release, mslicer publishes its benchmark method and models, and DragonFruit has plugins and an alliance behind it.

## On this page

1. [The four projects in one table](https://encrust.app/blog/open-source-resin-slicers-compared/#the-four-projects-in-one-table)
2. [Speed figures are not comparable yet](https://encrust.app/blog/open-source-resin-slicers-compared/#speed-figures-are-not-comparable-yet)
3. [Where each project stands out](https://encrust.app/blog/open-source-resin-slicers-compared/#where-each-project-stands-out)
4. [What to know before you use Encrust](https://encrust.app/blog/open-source-resin-slicers-compared/#what-to-know-before-you-use-encrust)

We build Encrust and we recommend it, so read this table as one project’s account of its neighbours. Each cell comes from the project’s own page or repository, opened on 5 November 2026; Encrust’s own cells were re-read on 17 November 2026\. If a project has moved on, [tell us in Discussions](https://github.com/vvvlladimir/Encrust/discussions) and the correction goes here with its date.

## The four projects in one table

|                     | Encrust                                                                                                | DragonFruit                               | mslicer                    | UVtools                                         |
| ------------------- | ------------------------------------------------------------------------------------------------------ | ----------------------------------------- | -------------------------- | ----------------------------------------------- |
| What it is          | Slicer                                                                                                 | Slicer                                    | Slicer                     | Analysis, repair and conversion of sliced files |
| Licence             | AGPL-3.0                                                                                               | AGPL-3.0-or-later                         | GPL-3.0                    | AGPL-3.0                                        |
| Slicing code        | Rust                                                                                                   | Rust, under a Next.js and Tauri interface | Rust                       | C#                                              |
| Desktop releases    | Windows, macOS, Linux                                                                                  | Windows, macOS, Linux                     | Windows, macOS, Linux      | Windows, macOS, Linux                           |
| Browser release     | Yes                                                                                                    | None listed                               | None listed                | None listed                                     |
| Formats written     | 20+, listed in [the format table](https://github.com/vvvlladimir/Encrust/blob/v0.9.0/docs/features.md) | Plugins, no list on its page              | .ctb, .goo, .nanodlp, .svg | Not a slicer; it converts between formats       |
| Stated status       | Beta                                                                                                   | Beta                                      | No label                   | No label                                        |
| Latest release seen | v0.9.0, 17 November 2026                                                                               | v0.3.1 (pre-release), 3 November 2026     | v0.10.1, 2 November 2026   | v7.1.2, 26 October 2026                         |

## Speed figures are not comparable yet

Every number below is its project’s own, and no two share a model or a computer.

| Project     | Its figure                                        | The test behind it                                                                                                                                                                                   |
| ----------- | ------------------------------------------------- | ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- |
| Encrust     | 0.72 s on seven threads, 1.2 s in a browser       | A 998,000-face sphere, [Elegoo Mars 4 Ultra panel, 0.05 mm layers, 8 cores](https://github.com/vvvlladimir/Encrust/blob/v0.9.0/docs/design/web-build.md#measured-2026-10-04), slice, write and check |
| DragonFruit | 1.01 s                                            | One model, Puck the Adventurer, sliced and written; hardware not stated on its page                                                                                                                  |
| mslicer     | “Often 20× to 120× faster than competing slicers” | [Stanford Dragon and two other models](https://mslicer.com/docs/benchmark), Core Ultra 7 165H laptop, Saturn 3 Ultra, against CHITUBOX, Lychee and Photon Workshop                                   |

mslicer’s page is the only one of the three that times itself against other slicers. We know of no run of the three on the same files, and we haven’t done one ourselves. Until one exists, this table can’t tell you which of the three is fastest.

## Where each project stands out

Encrust is the one we recommend. After slicing it reads back the file it wrote and [walks every layer for islands, suction cups and thin sections](https://github.com/vvvlladimir/Encrust/blob/v0.9.0/docs/features.md), so you see a failed layer before the vat does. It has 199 printer profiles and writes each printer’s own format, from .goo and .ctb to .pwmx, .cxdlp and .sl1\. Supports, hollowing with drain holes and auto-orient are built in, and a command line (`encrust`) runs the same pipeline for scripts. When you can’t install anything, open it in a browser tab: the same code runs there and nothing is uploaded. Only sending to a printer over the network needs the desktop app.

DragonFruit comes from the Open Resin Alliance, and printers, formats and print-side steps are plugins rather than a fixed list. It’s worth following if you want an open stack with more than one person behind it.

mslicer publishes its method, which makes it the easiest of the three to check. It writes four formats, so look for yours first.

UVtools is the older and larger project of the four by GitHub stars (about 1,650 against about 90 for each of the two slicers above and 15 for Encrust, on 17 November). It opens a file any slicer wrote, so it also fills the gap for anyone staying on a closed slicer.

## What to know before you use Encrust

Encrust is in beta. Its 199 printer profiles come from makers’ specifications and the format notes, and it ships no resins, so set the exposure from your resin maker’s instructions and print a calibration piece first, as with any new slicer. It has no plugin system.

## Sources

- [DragonFruit: project page](https://dragonfruit-slicer.com/)  · The 1.01 s figure, the platforms, the plugin design and the beta notice
- [DragonFruit: repository](https://github.com/Open-Resin-Alliance/DragonFruit)  · Licence and the Rust, Next.js and Tauri stack
- [mslicer: repository](https://github.com/connorslade/mslicer)  · Licence, the four formats and the 20× to 120× claim
- [mslicer: benchmark](https://mslicer.com/docs/benchmark)  · The models, the laptop and the slicers it was timed against
- [UVtools: repository](https://github.com/sn4k3/UVtools)  · What it does and its licence

## More in Resin printing

- [Halve the layer height and the exposure does not halve ](https://encrust.app/blog/resin-exposure-when-layer-height-changes/)
- [A resin slicer in a browser tab ](https://encrust.app/blog/resin-slicer-in-a-browser-webassembly/)
- [Which file does your resin printer read? ](https://encrust.app/blog/which-file-format-resin-printer/)
- [Read the layer check before you print ](https://encrust.app/guides/read-the-layer-check/)
- [All posts ](https://encrust.app/blog/)

---

[ Encrust](https://encrust.app/)

Free and open source under AGPL-3.0, written in Rust. Your files stay on your computer.

## Product

[Download](https://encrust.app/download/) [Printers](https://encrust.app/printers/) [Web app](https://encrust.app/app/)

## Learn

[Guides](https://encrust.app/guides/) [Blog](https://encrust.app/blog/) [FAQ](https://encrust.app/faq/) [Changelog](https://github.com/vvvlladimir/Encrust/blob/main/CHANGELOG.md)

## Project

[About](https://encrust.app/about/) [Source code](https://github.com/vvvlladimir/Encrust) [Discussions](https://github.com/vvvlladimir/Encrust/discussions) [Report a bug](https://github.com/vvvlladimir/Encrust/issues)

Encrust prepares files for machines that cure resin with UV light. It can’t know whether your settings suit your resin, printer or model, so check its output before a long print. Provided without warranty, as the licence says.

[Privacy](https://encrust.app/privacy/) [Impressum](https://encrust.app/impressum/) [Datenschutzerklärung](https://encrust.app/datenschutz/)
