Encrust
Alle Anleitungen

Noch nicht auf Deutsch übersetzt, daher die englische Fassung.

Modell vorbereiten · Anleitung 13 von 21

Read the layer check before you print

10 Min. Lesezeit

Check lists what is wrong on the plate at once, then reads every layer as Encrust would write it and lists where the print is likely to fail. An island cures over nothing and fails the print. A lever is a thin neck pulled off-centre. A peel is a layer the film pulls hard on. Each comes with its numbers.

Before you start

Have a model on the plate with a printer and resin chosen, and supports added if the model needs them (Supports). The check judges the layers as they will be written, supports included, so run it after you have supported the model, not before. On the plate needs only the models in place.

Open the Check tool

Click Check in the tool row over the view, or press 9. Encrust cuts the stack and measures it (“Reading every layer of the stack…”), and the tool’s card opens at the left edge of the view. Its heading says “no issues” or “N issues” once the reading is done, and counts the plate’s issues with the layers’. Without a printer chosen, the card has nothing to read: “The check reads the layers, which are cut as soon as there is a model on the plate and a machine to cut it for.”

The card has two parts, top to bottom:

  • On the plate: what is wrong with where the models stand, in two cards, Placement (outside the build volume, in the plate inset, meeting another model) and Hollow and drain (hollow with no drain hole, worth hollowing). It needs no layers, so it appears at once.
  • In the layers: one card for each kind the layers show: Islands, Suction cups, Weak necks, Hard peel and Thin sections. A kind with nothing to report has no card. When the layers show nothing at all, a card reads “Nothing found to fail on”.

At the foot of the card, Fix all moves models out of the way, drills drain holes and suction cup vents, then stands supports, in that order, and one undo reverts it all. It shows only while something can be fixed that way. Each card also has its own buttons, named below.

Check on the tool row carries a dot as soon as any issue stands, even with the card closed: red for the gravest kind, amber for the rest.

A row in a layer card reads “Layer 212” and, at its right, the numbers, such as 0.02 mm² on an island. Click a row and the view jumps to that layer and flies the camera to the issue. The heading In the layers has arrows to the previous and the next issue. The list shows seven rows and scrolls; past 200 rows it counts the rest. Every issue also has a bar on the layer strip down the right edge, in the danger colour for what will fail and the warning colour for what may, so you can see where up the print they sit. The strip’s three buttons, named Model, Model and layer side by side, and Layer mask, switch between the model, the model beside its layer, and the layer alone.

Levers and peels are not judged in the bottom layers, which the build plate holds rather than the model. Islands are judged on every layer.

Read what is on the plate

On the plate is found as soon as the models stand still, before any layer is read. It lists the model and, at its right, what is wrong. Click a row and the camera flies there; on a model that meets another, each further click goes to the next place.

Row reads Colour What it means
outside the build volume danger The model, its supports or its raft stand outside the volume; the overhang is cut off the layers. The view stripes it red.
in the plate inset warning It reaches into the margin a printer keeps clear along the plate’s edges. It still slices whole.
meets other model danger The models, or a model’s supports or raft and another model, touch. They would slice as one piece. The model’s row in the Models card carries Meets.
hollow with no drain hole warning No hole drains the cavity, so it prints full of resin. A click opens the Drain tool on it.
worth hollowing warning A solid model whose wall in the Hollow tool would save at least 10 ml and 40 % of its resin. A click opens the Hollow tool on it.

The bounds need a printer; the other rows do not. None of it stops the slice (what each row means). A gap of any width is not touching; touching counts.

Islands

An island is a piece of a layer that touches nothing in the layer below. It cures over nothing, sticks to the film and stays in the vat.

A row reads island · 0.02 mm²: the area of the piece, summed when a layer has several. On the layer itself, the island’s pixels are painted in the danger colour. Pieces under 0.01 mm² are treated as specks of edge grey and not listed.

Each layer is judged against the layer below it as written, supports included. Fix an island one of three ways:

  • Add or move a support under it (see supports).
  • Click Support them, which stands a support under each island and each hanging part, in a group named Islands, built to the support numbers in hand. The notice reads “Stood N supports in Islands”.
  • Click Remove them, next to it. Encrust erases the islands, and only the islands, from the file and checks again. The card then reads “N islands taken out of the file”, and Put the islands back undoes it.

A part that stood on a removed island stays in the file. It loses only its first layer, the one over the island, and the rest hangs over a gap. Check names it “Part left hanging” and lists it as hangs over nothing, until you support it (Support them stands a support under it). Remove the next N islands takes one more layer off each hanging part per click, so a part never goes in one click.

Removing suits specks you don’t care about. A part you do care about is better supported than trimmed. The setting is saved with the project. The command line has the same switch, --remove-islands, and --hanging-passes for the extra layers.

Levers

A lever is a thin neck under a part that the film pulls on from off to one side. For each piece, Encrust finds the narrowest section between it and the plate (the neck). It then takes the pull of the layer, adds the tension on the neck and the bending from the sideways offset, and compares the stress with 13 MPa, a warning level calibrated on one resin at 0.05 mm, not a limit that holds for every printer or resin (the calibration).

A row reads lever · 9.8 mm · 12 MPa: the offset between the pull and the neck, and the stress. A neck is named once, at its worst layer. The kind’s name on hover is “Weak neck”.

The usual fix is a support under the part’s centre, so the load doesn’t hang from one side of the neck.

Peel

A peel is a layer that pulls hard on the film as the plate lifts. A layer is flagged when its pull passes 30 N, the weight of about 3 kg and, by the pull Encrust works out, what a solid disc 73 mm across pulls. A run of such layers is named once, at the hardest. A row reads peel · 60 N, the pull of a solid disc about 94 mm across.

Tilting or hollowing the model lowers the pull (for hollowing, see hollowing).

The readings sit in the Hard peel card when a layer is flagged; with none flagged, a Peel section at the foot of the Check card shows them. They list the “Hardest pull” layer and “Pulls like a disc of” a diameter in mm. The disc is the round section that would pull equally hard. It also gives the “Widest step”, the layer whose area grows most over the one under it, and “Grows by” how many mm². These are readings, not warnings, so they show even when no issue was found. Like levers and peels, they skip the bottom layers.

Suction cups and thin sections

A suction cup is a hole that a layer closes in on every side and the layers below do not vent, so each lift pulls on the air-tight pocket. It is listed when a full vacuum on the hole would pull at least 10 N, a hole of about 99 mm², at its widest layer and holds at least 0.02 ml (the design note). A row reads suction cup · 99 mm². A drain hole lets the air in; the Drain tool makes one.

A thin section is a piece held from below that is narrower than 0.15 mm across, taken as a disc of its area, in a run at least 1 mm tall. A row reads thin · 0.08 mm. Check’s own words are that thin sections “may not form at all”; thicken it if it matters.

How far to trust the numbers

Every limit here is a warning level we set, not a failure measured on any printer or resin: 13 MPa for a neck, 30 N for a peel, 10 N (about 99 mm²) and 0.02 ml for a cup, 0.15 mm and 1 mm for a thin section.

The pull is a calculation, not a measurement. A section pulls with its area and, more weakly, with how far resin has to reach in from its edge, so a disc pulls harder than a star of the same area. How much harder is fitted to a disc and a star that Pan et al. (2017) pulled off a film. The overall scale is a factor we chose so that a 100 cm² disc pulls about 100 N, not one measured on a print (the design note). Pan pulled straight up off PDMS, while a tilting vat peels a PFA film, so the note takes the newtons as good to about a factor of three. What the number does get right is which of two layers pulls harder.

Treat a lever, a peel, a cup or a thin section as “look at this layer”. An island, or a part left hanging, is plain geometry: nothing is under it. A clean result means the check found nothing it can measure, not that the print will succeed. Exposure, lift and resin come first: follow your printer’s and resin maker’s instructions and start from a calibration piece.

If something goes wrong

The check says nothing and the print still failed. It reads geometry only: what each layer cures, what it touches below and how hard it pulls. It knows nothing of your exposure or the state of your film.

Hundreds of islands. The list shows the first 200 rows and counts the rest (“and N more layers”). A model with that many needs supports, not scrolling.

A part is missing its first layers after Remove islands. The island went, and the part that stood on it lost the layer over it and now hangs. Click Put the islands back and add the support the part needed, or click Support them, then check again.

The Check card only says “Checking”. The check reads the layers cut from the models on the plate, and only once a printer is chosen. It has nothing to read until there is a model on the plate and a printer to cut it for.

A model is marked outside the build volume and the slice still ran. Nothing in On the plate stops a slice; the overhang is cut off the layers. Move the model back, or click Scale to fit on its row in Placement, then check again.

Quellen