Encrust
All guides

Preparing a model · Guide 8 of 21

Hollowing and drain holes

7 min read

A hollow model with no way out prints full of liquid resin. Open Hollow (key 4), keep the 2 mm wall and press Hollow, then open Drain (key 5) and press Check drainage. Encrust paints each cavity the resin can't leave, and Drill a hole into each cuts a hole into every pocket.

Before you start

This picks up where Your first print leaves off: a printer and resin chosen, and a model on the plate, placed and oriented the way you will print it. Hollow before you add supports, so they go on the final shape. The drainage check slices the plate, so it uses the layer height set for the printer and resin. The numbers below are starting points for one model. Your printer’s and resin maker’s instructions come first.

Hollow and Drain are the fourth and fifth tools in the tool row over the view, keys 4 and 5. Each works on the models you selected, or on every visible model on the plate when none is selected. With one model selected, the settings you change are that model’s own; with none, they are the plate’s.

Hollow the model

  1. Open Hollow. Under Shell, pick Inside, Outside or Bottom open.
    • Inside grows the wall inward and leaves the outside as imported.
    • Outside builds a mould around the model. It takes no infill and keeps no wall solid, so the card hides both.
    • Bottom open grows the wall inward and cuts the floor the model stands on away, so the cavity drains with no hole. On the plate it stays sealed until the print comes off, so the card tells you to add a small vent near the top.
  2. Set Wall. The default is 2 mm. The card takes 0.15 to 15 mm, and 0.15 mm is the thinnest wall the lattice can resolve. The wall is measured on the plate, at the model’s current scale, so type the wall you want printed.
  3. Leave Precision at its default, 50 %, unless the cavity looks coarse. It sets how smooth the cavity is, and the line under it shows the lattice in millimetres. It is not the layer height.
  4. Click Hollow at the foot of the card. A progress bar shows the run, and Cancel stops it inside the model it is on.

Under Already done, the card now shows Hollowed and Resin saved in ml. Make solid again undoes it. A wall thicker than the model leaves no cavity, and the model comes back unchanged. A stray shell left inside a sculpt gets no wall of its own: it stays in the model and prints solid.

The card’s own note says why this matters: “A cavity needs a drain hole, or the resin trapped inside can crack the part later.” Drain holes come two sections down.

Fill the cavity

Infill is off by default and the cavity is left empty. Switch Infill on to fill it with a lattice and pick a pattern:

Pattern Shape
Hive hexagonal cells standing on the plate
Grid square cells standing on the plate
Scaffold struts on the edges of a cube stood on its corner

Every pattern takes a cell size and a Density. The cell is Hexagon diameter for a hive, Cell width for a grid and Cell for a scaffold. The defaults are a hive, an 8 mm cell and 25 % density. The card works out how thick the walls or struts come out and warns when that is under 0.5 mm, too thin to print.

Hive and grid cells are joined to their neighbours by round holes, so resin runs from cell to cell and one drain hole empties all of them. A scaffold has no cells to seal. None of its struts is level, so none starts in mid-air. Infill gives back some of the resin hollowing saved. A hollow or infilled model is not made fit for load-bearing or safety-critical use by either.

Keep the wall solid

A thin spar or spike can print hollow and snap. Under Keep solid, click the model where the wall must stay solid and Encrust drops a blocker there. Shift-click runs a rod on from the last blocker, to keep a whole limb solid. Alt-click a blocker to take it away. Place blockers before you click Hollow.

For thin parts everywhere at once, switch on Keep thin parts solid on the Hollow card. Where the model is thinner than the set width, it stays solid, so fingers and blades are not hollowed. The width starts at 6 mm and the card takes up to 50 mm.

Fit to thickness fills the model where you click, as thick as it is there. Fixed size reaches Past the wall into the cavity by the distance you set, 4 mm by default. Clear N blockers takes them all away at once. A blocker is a ball, or a rod, of solid the cavity is cut around.

Place drain holes

Open Drain. Under Opening, with Hole picked, a click on the model or its raft cuts a hole at once, hollow or not. Supports are never cut: a click passes through them. Alt-click a hole to take it away. A click on the floor of a hole drills on through it. Only Bottom open drains without a hole. With Inside, the resin needs a hole or a channel to leave by.

  • Hole size: 3 mm by default, 0.5 to 20 mm.
  • Depth: 3 mm by default, measured from the surface inward. A hole you place by hand is exactly as deep as typed, on a hollow model too. Set short of the wall, it is a dimple that does not drain and leaves resin trapped, so run Check drainage before you slice. Holes Encrust chooses, by Auto or Drill, are deepened until they are through the wall.
  • Taper: 1 is a cylinder, lower values make a cone.
  • Round or Polygon, with Sides and Turn. In a side wall, turn a polygon until a corner is at the top: a pointed roof prints without sagging.

For a long path, switch Opening from Hole to Channel. Each click adds a point, and the channel runs as a tube of the hole’s width and outline under all of them, open at its two ends only. Click Dig the channel, which counts the points you laid. On a model that is already hollow, Encrust hollows it again around the channel on its own.

A hole drilled into a model that is still solid is part of its shape, not a drain. When you hollow it later, the cavity keeps a wall around the hole and the hole does not drain. Hollow first, or drill the drain after.

Every hole also gets a plug under Plugs: a piece that sits on the plate beside the model and fits the hole, narrower all round by Gap per side, 0.15 mm by default. A plug seals the cavity again, and resin sealed in can stay liquid: clean and cure the model by your resin maker’s instructions before you plug, and treat a plugged cavity as holding uncured resin if you did not.

To let Encrust choose, click Auto beside Check drainage. It looks for a drain hole and a vent for each pocket of trapped resin in the selected models, and drills those that a new check confirms let the resin out. The status line counts the holes drilled and any pockets it could not drain, which stay red. Look over the result yourself before you print.

Check for trapped resin

Trapped resin is uncured resin sealed in a cavity with no way out. A model printed that way comes off the printer with that resin still liquid inside. Treat it as holding uncured resin and follow the safety data sheet section below.

Click Check drainage. Encrust slices the plate, follows the air through the layers and reports every pocket that never reaches the plate, the edge of the layers or the top of the model. It counts the holes and channels you cut, an infill cell that seals itself and a blocker that walled a cavity off. Pockets under 5 mm³ are droplets the wash takes out and are not reported.

Under Trapped resin the result is either “Nothing is trapped: the resin can get out of every model on the plate”, or a red line saying how many ml cannot get out, over one row per pocket with its volume and a Drill button of its own. Turn on See through models (View menu, or the icon in the view) to see each pocket painted red inside the cavity.

Click Drill a hole into each. Each hole goes in at the lowest point of its pocket, from the nearest surface and deep enough to reach it, with the hole size and taper you set. The check button now reads Check again: click it to confirm.

Check does the same without being asked. Its On the plate list marks a hollow model whose holes don’t drain its cavity as “hollow with no drain hole”, and a solid model that hollowing would save at least 10 ml and 40 % of its resin on as “worth hollowing”.

Uncured resin and the SDS

Handling, protective equipment, cleaning and disposal of uncured resin are set out in your resin maker’s safety data sheet (SDS). Read it, and follow it. Disposal follows your local rules for hazardous waste: never down the drain, never uncured resin in household waste.

If something goes wrong

The Hollow button is greyed out

The card says why: “Nothing visible on the plate to hollow.” Show the model, or put one on the plate.

A note says the cavity was cut on a coarser lattice

The model needed more memory than the budget allows. The run finished, with a coarser cavity than Precision asked for.

“The numbers have moved since. Hollow again to catch up.”

You changed a setting or rescaled the model after hollowing. The wall scales with the model, so click Hollow again.

The check reports a pocket you think is open

A passage narrower than a tenth of a millimetre reads as closed. The cost is a hole you didn’t need.

Sources