Encrust
Печать смолой, форматы файлов и устройство слайсера

На Русский ещё не переведено, поэтому показана английская версия.

Печать смолой

Open-source resin slicers, side by side

4 мин чтения

Three open-source resin slicers written in Rust are out today: Encrust, DragonFruit and mslicer. UVtools works on files that are already sliced. Encrust checks every layer of the file it writes and is the one of these with a browser release, mslicer publishes its benchmark method and models, and DragonFruit has plugins and an alliance behind it.

We build Encrust and we recommend it, so read this table as one project’s account of its neighbours. Each cell comes from the project’s own page or repository, opened on 5 November 2026; Encrust’s own cells were re-read on 17 November 2026. If a project has moved on, tell us in Discussions and the correction goes here with its date.

The four projects in one table

Encrust DragonFruit mslicer UVtools
What it is Slicer Slicer Slicer Analysis, repair and conversion of sliced files
Licence AGPL-3.0 AGPL-3.0-or-later GPL-3.0 AGPL-3.0
Slicing code Rust Rust, under a Next.js and Tauri interface Rust C#
Desktop releases Windows, macOS, Linux Windows, macOS, Linux Windows, macOS, Linux Windows, macOS, Linux
Browser release Yes None listed None listed None listed
Formats written 20+, listed in the format table Plugins, no list on its page .ctb, .goo, .nanodlp, .svg Not a slicer; it converts between formats
Stated status Beta Beta No label No label
Latest release seen v0.9.0, 17 November 2026 v0.3.1 (pre-release), 3 November 2026 v0.10.1, 2 November 2026 v7.1.2, 26 October 2026

Speed figures are not comparable yet

Every number below is its project’s own, and no two share a model or a computer.

Project Its figure The test behind it
Encrust 0.72 s on seven threads, 1.2 s in a browser A 998,000-face sphere, Elegoo Mars 4 Ultra panel, 0.05 mm layers, 8 cores, slice, write and check
DragonFruit 1.01 s One model, Puck the Adventurer, sliced and written; hardware not stated on its page
mslicer “Often 20× to 120× faster than competing slicers” Stanford Dragon and two other models, Core Ultra 7 165H laptop, Saturn 3 Ultra, against CHITUBOX, Lychee and Photon Workshop

mslicer’s page is the only one of the three that times itself against other slicers. We know of no run of the three on the same files, and we haven’t done one ourselves. Until one exists, this table can’t tell you which of the three is fastest.

Where each project stands out

Encrust is the one we recommend. After slicing it reads back the file it wrote and walks every layer for islands, suction cups and thin sections, so you see a failed layer before the vat does. It has 199 printer profiles and writes each printer’s own format, from .goo and .ctb to .pwmx, .cxdlp and .sl1. Supports, hollowing with drain holes and auto-orient are built in, and a command line (encrust) runs the same pipeline for scripts. When you can’t install anything, open it in a browser tab: the same code runs there and nothing is uploaded. Only sending to a printer over the network needs the desktop app.

DragonFruit comes from the Open Resin Alliance, and printers, formats and print-side steps are plugins rather than a fixed list. It’s worth following if you want an open stack with more than one person behind it.

mslicer publishes its method, which makes it the easiest of the three to check. It writes four formats, so look for yours first.

UVtools is the older and larger project of the four by GitHub stars (about 1,650 against about 90 for each of the two slicers above and 15 for Encrust, on 17 November). It opens a file any slicer wrote, so it also fills the gap for anyone staying on a closed slicer.

What to know before you use Encrust

Encrust is in beta. Its 199 printer profiles come from makers’ specifications and the format notes, and it ships no resins, so set the exposure from your resin maker’s instructions and print a calibration piece first, as with any new slicer. It has no plugin system.

Источники