Encrust

От первой модели до первой печати

В первый раз читайте по порядку: каждая инструкция начинается там, где закончилась предыдущая. Потом переходите сразу к нужному шагу.

Начать с первой инструкции

Первые шаги

  1. Установка Encrust

    На Windows ставьте Encrust из Microsoft Store: без предупреждений, а обновляет его сам Store. На macOS и Linux скачайте файл для своей системы со страницы последнего релиза. Файлы не подписаны, поэтому на macOS перед первым запуском нужна одна команда в Терминале. На Linux ничего лишнего не требуется.

    4 мин чтения
  2. Первая печать

    В итоге у вас будет небольшая пластина проверки экспозиции, нарезанная под ваш принтер с экспозицией вашей смолы. Добавьте принтер и смолу в окне «Принтер и смола», поставьте на платформу пластину «Проверка экспозиции», посмотрите, что найдёт «Проверка», и нарежьте файл, который читает принтер.

    7 мин чтения
  3. Save a project and come back to itEN

    Press Cmd+S (Ctrl+S on Windows and Linux), name the file, and the plate is saved as an .encrust project: models, the supports you placed, the hollow shell, and which printer and resin it was for. Print settings are not kept. File > Open project... brings the plate back: a hollowed model opens hollow, and a support stands where it was grown.

    8 мин чтения

Подготовка модели

  1. Move, rotate, scale and auto-orientEN

    Pick a model with the Select tool. Auto-orient turns it for the preset beside it: Auto, Supports, Peel or Time. With a printer chosen it test-prints its best poses before picking one. Lay on face puts a clicked face down. Move, Rotate, Scale and Place do the rest by hand.

    11 мин чтения
  2. Check and repair a modelEN

    Encrust welds, orients and counts every mesh as it opens, and tags a model Broken when holes, faces without area or faces drawn twice are left. Press 3 for the Repair tool, read what it found, pick a method and click Repair. It adds no surface unasked and leaves a model as it came if a repair would leave it with more defects.

    9 мин чтения
  3. Cut and split a modelEN

    To cut a model, press 6, choose an axis, set the position in millimetres and click Cut. Each half closes with a flat face and lands on the plate as its own model. Join the halves adds dowels, pins, magnets or a key, so the pieces glue back true. About ten minutes.

    10 мин чтения
  4. Arrange models and use more than one plateEN

    Click Arrange the plate in the Models card: Encrust packs every visible model, with the supports and raft already built for it, into the plate with the Gap you set (5 mm by default). A model that doesn't fit stays put and a message says it found no room. Send it to another plate with Edit > Move to plate.

    6 мин чтения
  5. Полая модель и дренажные отверстия

    Если смоле некуда вытечь, полая модель печатается с жидкой смолой внутри. Откройте «Полость» (клавиша 4), оставьте стенку 2 мм и нажмите «Сделать полой», затем откройте «Дренаж» (клавиша 5) и нажмите «Проверить дренаж». Encrust закрасит каждую полость, откуда смоле не вытечь, а «Просверлить отверстие в каждом» прорежет отверстие в каждом кармане.

    7 мин чтения
  6. Поддержки: автоматически и вручную

    Новая платформа начинается с профиля Auto: он строит каждую поддержку как Light, Medium или Heavy, смотря что она держит. Откройте «Опоры» (клавиша 8), нажмите «Построить поддержки», и Encrust поставит поддержку под каждый остров и нависание. Потом отдельные поддержки можно расставлять, закрашивать, выбирать и двигать вручную.

    8 мин чтения
  7. Press a texture into the surfaceEN

    Press 7 for the Relief tool, keep the Texture mode, choose a built-in texture, your own picture or the texture an OBJ or 3MF brought, set Depth in millimetres and click Press it in. White raises the surface by the Depth, black leaves it. Press before supports. Text and Combine have their own guides.

    9 мин чтения
  8. Write text on a modelEN

    Press 7, click the Text icon, type the words, choose Raised or Sunk, set Letter height and Depth in millimetres, then click the model where the text goes. The letters join the model exactly, with its sharp edges kept. About five minutes.

    6 мин чтения
  9. Combine models: union, subtract, intersectEN

    Pick two or more models, press 7, click the Combine icon, choose Union, Subtract or Intersect and click Combine. Two 20 mm cubes overlapping by 10 mm come out as 15,000, 7,000 or 1,000 mm³. Subtract keeps the model you picked first and takes the rest out of it.

    6 мин чтения
  10. Read the layer check before you printEN

    Check lists what is wrong on the plate at once, then reads every layer as Encrust would write it and lists where the print is likely to fail. An island cures over nothing and fails the print. A lever is a thin neck pulled off-centre. A peel is a layer the film pulls hard on. Each comes with its numbers.

    10 мин чтения
  1. Printer, resin and support profilesEN

    In Machine and resin, Add a machine opens the library of bundled printers: pick one to install it, or choose Custom printer and enter panel, volume and file format. Each printer's Resins tab holds its own resins, retuned with Duplicate or taken from a sliced file. Every edit saves itself as a TOML file you can Export and Import.

    10 мин чтения
  2. Exposure, lift and rest timesEN

    Exposure is how long each layer is lit; lift, retract and waits decide how the plate moves between layers. Encrust keeps them in the resin, per printer, and hides every field your printer's firmware runs itself. This guide sets each one, and says which printers lock which.

    11 мин чтения
  3. Layer height, adaptive layers and anti-aliasingEN

    Slice at the layer height your resin maker gives an exposure for, and leave Edge smoothing on Balanced. Adaptive height works only on a printer you have marked as accepting variable layers, which no bundled profile does. The other looks, Grey levels, Edge blur and the edge grey range are for tuning an edge once a print shows a problem.

    10 мин чтения
  4. Get the size rightEN

    Print a test part at 100 % Shrinkage, cure it, measure it cold and divide: percent = 100 x drawn / measured. A 20 mm bar measuring 19.90 mm wants 100.503 %. Enter it under Shrinkage in the resin's Compensation card, with its switch on. Tight holes (a, under Tolerance) and the time estimate (Unaccounted per layer) are separate.

    8 мин чтения
  5. Открыть нарезанный файл и проверить слои

    Encrust открывает .goo, .ctb, .pwmx и другие нарезанные файлы как модель, восстановленную из слоёв: её можно подвинуть, заново поставить поддержки или нарезать для другого принтера. Собственных слоёв файла окно не показывает. Это делает командная строка: encrust info выводит заголовок и декодирует каждый слой.

    6 мин чтения
  6. Convert a sliced file to another formatEN

    You'll end with the same layers in another printer format, such as .ctb to .goo, with no model and no new slice, in a few minutes. Encrust copies the masks unchanged, so the printer's panel must match the file's. On any other panel, the file has to be sliced again.

    8 мин чтения
  7. Слайсер в командной строке

    Команда encrust — это слайсер для фотополимерной печати в терминале. Без окна программы она нарезает модель, платформы проекта или целую папку в файл для принтера, например .ctb или .goo, и управляет принтером в вашей сети. С --json каждый запуск выводит один документ JSON, а код выхода сообщает скрипту, чем всё закончилось.

    10 мин чтения

Помочь проекту

  1. Confirm your printer with one test printEN

    A profile is confirmed when someone prints an Encrust file on that machine. Slice a small piece in your printer's own software, slice the same piece in Encrust, compare what both files state, print Encrust's, then report the result on GitHub with the vendor's file attached. Plan for the length of one small print.

    5 мин чтения