Encrust
Все инструкции

На Русский ещё не переведено, поэтому показана английская версия.

Подготовка модели · Инструкция 11 из 21

Write text on a model

6 мин чтения

Press 7, click the Text icon, type the words, choose Raised or Sunk, set Letter height and Depth in millimetres, then click the model where the text goes. The letters join the model exactly, with its sharp edges kept. About five minutes.

Before you start

You need a closed model on the plate, as in Your first print. If the Models card tags it Broken, repair it first (Check and repair a model). Text is only ever cut exactly: Encrust patches a torn model where it is broken first, and a model no patch can close is refused and left as it was.

Write before you hollow or support. The result replaces the model, and its supports, cavity, holes, own settings and texture are not kept. Undo puts the original back (what Text keeps).

A flat label goes no deeper than the Depth you set, measured from the face you click. A pillar beside the label, or the far side of a thin wall, is not the face being written on and is passed over, so no letter reaches more than twice the Depth off its plane (how letters stand on the model). Nothing beside the letters is cut.

Open the Text mode

  1. Press 7, or click Relief on the tool row over the stage.
  2. In the card’s heading, click the Text icon, the second of the three. The question mark beside the card’s name reads “Text raised out of a model or sunk into it, where you click.”

The card has two sections, Text and Lettering, and a line at the foot: “Click the model to place the text.” When the text cannot be made, that line gives the reason instead.

Type the words and choose a font

  1. In Text, type the words. The box starts with “Encrust”. A new line starts a second row; the rows are centred on each other, and the block is centred on your click.
  2. Click the font field under the box to choose a family. Encrust starts with the built-in IBM Plex Sans, and reads the fonts installed on your computer the first time you open the list (“Reading the fonts installed on this machine…”). Type in the search field, Find a font, to filter by name, and click a family or press Enter for the first match. A font has a licence of its own: check that it allows the use you have in mind, such as printing and selling lettering. IBM Plex Sans is published under the SIL Open Font License.

Encrust writes each family in its regular face. If a font has no letter for a character, the foot of the card says “this font has no letter for” that character; pick another font or change the text.

Scripts that join their letters, Arabic and Devanagari, are not shaped. The browser build offers only IBM Plex Sans (the limits).

Set the lettering

Under Lettering:

Setting Choices or range Default
Raised / Sunk Out of the surface, or into it Raised
Flat / Follow the surface How the letters meet the face Flat
Letter height 1 to 100 mm, the height of capitals 6 mm
Depth 0.1 to 10 mm 0.8 mm
Angle 0 to 360°, anticlockwise about the face’s normal 0°

The defaults are starting points, not values tested on a printer; your printer’s and resin maker’s instructions come first for how small a letter your setup holds.

Flat measures the Depth from the face where you click and follows it no further than that, so on a curved face the letters stay flat. Follow the surface bends every letter onto the face under it, so it stands the full Depth out of a curved face, or into it, everywhere. On a steep slope the walls of a letter stay square to the plane at the click, so a letter is thinner across the slope by the cosine of the angle (following the surface).

On a wall, the text stands upright. On a face within 8° of level, a top face, the top of the line points to the back of the plate. Angle turns it from there.

Place the text

  1. Move the cursor over the model. A preview of the letters follows it in the view, standing as they would after the click.
  2. Click. The model is picked, and a bar reads “Stamping the text”, with Cancel.
  3. Read the notice at the foot of the stage: “Wrote on” and the model’s name.

Cmd-click (Ctrl-click on Windows and Linux) picks a model without writing on it.

Text is joined with an exact boolean, never through a field: a field would mesh the whole model again at its lattice and round every edge of it for the sake of a few letters. Only the side of the model the letters stand on goes through the engine, and is stitched back along the cut (joined exactly). Raised adds the letters to the model; Sunk takes them out of it.

From the command line

encrust slice part.stl --label "No 7" --label-at 20,10,30 --label-sunk -o part.goo writes sunk text on the surface nearest that plate point, given in millimetres. --label-height, --label-depth, --label-follow, --label-angle and --label-font (a font file) match the card, with the same defaults (CLI reference). Modelling runs before the models are hollowed and supported, as in the window.

If something goes wrong

The foot of the card gives a reason and a click does nothing

The line reads the reason the text cannot be made: “there is nothing to write” for an empty box, “this font cannot be read” for a damaged font file, “this font has no letter for” a character, or “the letters need a height and a depth”. Fix the field it names.

“the model is not a closed solid, so it cannot be cut exactly; repair it first”

No patch can close the model. Open the Repair tool (key 3) and repair it, or fix it in the program that made it, then click again (Check and repair a model).

“the text does not stand on the model there”

No part of the lettering has the model beneath it, as when the click is on the very rim of a face and the letters hang off it. Click nearer the middle of the face.

Источники