Encrust
All guides

Getting started · Guide 2 of 21

Your first print

7 min read

You'll end with a small exposure plaque sliced for your printer, carrying your resin's own exposure. Add the printer and resin in Machine and resin, put the Exposure check plaque on the plate, read what Check finds, then slice the file your printer reads.

Before you start

Install Encrust first (Install Encrust). You don’t need a model of your own: this guide prints a test plaque that ships with Encrust. Have two things from your resin’s maker at hand: the exposure they give for your printer, and the resin’s safety data sheet (SDS).

Add your printer

A fresh Encrust has no printer and no resin yet. The chip in the top bar reads “Select a printer”, and a notice at the foot of the window says “No printer or resin yet”.

  1. Click Set up in that notice, or open File > Machine and resin….
  2. Click Add a machine, then your printer’s brand, then the model. If you know the name, type it into Search every machine.

Your printer joins the list on the left, open on its Resins tab. The plate takes it straight away, because it had no printer before; a printer you add later waits until you pick it in the chip. If yours isn’t in the library, Custom printer at the top right starts an empty profile.

Each printer profile knows what its firmware runs by itself. The Elegoo Saturn 4 Ultra is a good example: it separates each layer by tilting its vat, and a file that dictates a per-layer lift stalls its plate. Its profile leaves lift and retract to the firmware, so on that printer the resin form shows no motion fields at all.

Add a resin and type its exposure

  1. On the Resins tab, click Add a resin. The new resin opens in its form.
  2. Find the card named for your printer, for example Exposure on the Saturn 4 Ultra. Set Layer height first, then Exposure, Bottom exposure and Bottom layers to your resin maker’s numbers for your printer.

Layer height goes first because changing it carries the exposure along, and the form shows the result under the field: “Carried from 2.50 s at 0.050 mm to 0.030 mm.” There’s no save button: the form saves as you type. The first resin goes on the plate by itself, the same way the printer did.

A new resin starts from 0.05 mm layers, 2.5 s exposure and 30 s bottom exposure over 6 bottom layers. Type your resin maker’s values over them. Every value here is a starting point for one printer and one bottle, and the printer’s and resin maker’s instructions come first.

A value outside what the printer’s maker advises gets a red frame and the allowed range. On the Saturn 4 Ultra, Bottom layers outside 2 to 10 shows “Its maker advises 2–10”, taken from its profile.

Click Every resin at the top of the form to return to the table, then close the window. The chip now names your printer and resin, followed by the layer height and exposure, for example “50 µm · 2.50 s”.

Put the exposure check on the plate

Open File > Test prints > Exposure check. The start page has the same list under its Test prints tab.

The plaque is 46 × 30 mm and 2 mm thick, with four rows of features 4 mm tall: pins 0.3 to 1.0 mm across, fins 0.2 to 0.8 mm, slots 0.1 to 0.5 mm and holes 0.4 to 1.2 mm. Underexposed, the thinnest pins and fins break off. Overexposed, the narrowest slots and holes close up. It prints flat on the plate, without supports.

Crustling, first in the same menu, is the project’s 30 mm tortoise, a 9 MB download on the first click. It makes a good second print once the plaque comes out right.

To print your own model instead, open File > Add model… (Cmd+I, or Ctrl+I on Windows and Linux) or drop the file on the window. Encrust opens STL, OBJ and 3MF.

Read the Check tool

Click Check, the last tool in the row over the view, or press 9. There’s nothing to start: Check reads the layers as soon as there’s a model on the plate and a printer to slice for.

On the plate comes first: a model outside the build volume, two models touching, a hollow with no drain hole. Below it come the kinds the layers show, each in its own card; click a row to jump to its layer. On a clean plate the card reads “Nothing found to fail on”.

Fix islands before you slice. An island is a part that starts in mid-air: it cures onto the film and stays in the vat. The Islands card offers Support them and Remove them. A weak neck, a hard peel, a suction cup or a thin section is a warning level to look at rather than a certain failure. If Check marks the plaque’s finest pins or fins as thin, leave them: showing where they stop forming is the plaque’s job. Read the layer check covers each kind.

Then check the exposure the file will carry. Press M until the view reads “Model and layer side by side”, click the layer number in the strip and type 1. Exposure in the plate card should match your bottom exposure.

Slice the plate

Click Slice to .goo at the foot of the plate card, or press Cmd+Enter (Ctrl+Enter), and choose where to save. The button names your printer’s own format, so a printer that reads .ctb shows Slice to .ctb.

A notice then reads “Wrote” with the path, the layer count, the resin volume in ml and the weight in g.

Copy the file to your printer and start the print there. If the printer is on your network, the plate card offers Slice and send, then Start print once the file has arrived.

To look inside a sliced file, run encrust info on it: it prints what the file states and decodes every layer. Open a sliced file uses it to compare your plaque with the same model from another slicer.

Once the plaque prints well on your printer, click Report a test print on its page under Printers. Your report confirms the profile for everyone with the same printer.

If something goes wrong

Slice to .goo is greyed out

The reason is under the button, or in its tooltip on an empty plate. “Pick a machine to know the panel to slice for.” means there’s no printer yet, and “Add a resin to this printer: an exposure is measured on your machine.” means there’s no resin; Set up fixes both. “Nothing visible on the plate to slice.” means the plate is empty or every model is hidden: click the eye at the start of the model’s row.

The notice adds “layers cut off at the edge of the panel”

Part of the model is outside the printer’s screen, and Check’s On the plate list marks it as outside the build volume. Press 1 for Select, click Centre or Scale to fit, and slice again.

The model is tagged Broken

The mesh can’t be sliced as it is, usually because its surface has a hole. Click the tag to read what’s wrong (“The surface is not closed: 3 edges have nothing on the other side”) and click Repair under it. For harder cases the Repair tool (key 3) has more methods: Check and repair a model on import.

Sources